When column 7 of the 172.101 table refers to a special provision for a hazardous material, the meaning and requirements of that provision are as set forth in this section. W100 Non-bulk flexible, fibreboard or wooden packagings must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner. In addition, MC 312 and DOT 412 cargo tank motor vehicles must: c. Have a MAWP or design pressure of at least 87 psig; and. 159 This material must be protected from direct sunshine and kept in a cool, well-ventilated place away from sources of heat. The identification number used must be consistent on package markings, shipping papers and emergency response information. If not impact resistant, the outer packaging should not be used as the sole means of protecting the battery terminals from damage or short circuiting. TP20 This hazardous material must only be transported in insulated tanks under a nitrogen blanket. 181 When a package contains a combination of lithium batteries contained in equipment and lithium batteries packed with equipment, the following requirements apply: a. Column 7 specifies codes for special provisions applicable to hazardous materials. B49 Tanks equipped with interior heater coils are not authorized. TP30 This hazardous material may only be transported in insulated tanks. In accordance with Special Provision 8 in 172.102, which is referenced in Column 7 of the Hazardous Materials Table (HMT; 172.101) for the entry "UN3082, Environmentally hazardous substance, liquid, n.o.s.," a hazardous substance that is not a hazardous waste may be shipped under the shipping description "Other regulated substances . 336 The use of UN1H1 drums, UN3H1 jerricans, and UN6HA1 composite packagings which meet the requirements of part 178 of the HMR at the Packing Group I or II performance level. When phlegmatized with water and inorganic inert material, the content of urea nitrate must not exceed 75 percent by mass and the mixture should not be capable of being detonated by test 1(a)(i) or test 1(a)(ii) in the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). Each inner packaging contains not more than 30 mL; b. Dry batteries not specifically covered by another entry in the 172.101 Table are covered by this entry (i.e., Batteries, dry, sealed, n.o.s.) W9 When offered for transportation by water, the following Specification packagings are not authorized unless approved by the Associate Administrator: woven plastic bags, plastic film bags, textile bags, paper bags, IBCs and bulk packagings. The operator of an aircraft carrying hazardous materials must do all of the following EXCEPT: A. In addition, the material also must be covered with an inert gas or the container must be filled with water to the tank's capacity. When portable tank instruction T75 is referenced in Column (7) of the 172.101 Table, the applicable refrigerated liquefied gases are authorized to be transported in portable tanks in accordance with the requirements of 178.277 of this subchapter. The rechargeable (and some non-rechargeable) types have gelled alkaline electrolytes (rather than acidic) making it difficult for them to generate hydrogen or oxygen when overcharged and therefore, differentiating them from non-spillable batteries. They will appear as a list of codes that are defined in 172.102 of the Code of Federal Regulations. Packagings may include a vent to permit the slow escape of gas (i.e. B16 The lading must be completely covered with nitrogen, inert gas or other inert materials. Wall thickness must be verified ultrasonically at intervals midway between periodic hydraulic tests (every 2.5 years). (i) Column 8: Packaging authorizations. Using the nominal capacitance (CN), rated voltage (UR) and the rated lower limit voltage (UL). Symbol Meaning Which is the correct column for hazardous materials? An unused lighter or a lighter that is cleaned of residue and purged of vapors is not subject to the requirements of this subchapter. 151 If this material meets the definition of a flammable liquid in 173.120 of this subchapter, a FLAMMABLE LIQUID label is also required and the basic description on the shipping paper must indicate the Class 3 subsidiary hazard. Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner. TP24 The portable tank may be fitted with a device to prevent the build up of excess pressure due to the slow decomposition of the hazardous material being transported. 130 Batteries, dry, sealed, n.o.s., commonly referred to as dry batteries, are hermetically sealed and generally utilize metals (other than lead) and/or carbon as electrodes. here. The pressure relief device must be preceded by a frangible disk in accordance with the requirements in 178.275(g)(3) of this subchapter to prevent crystallization of the product in the pressure relief device. Lithium ion cells and batteries at a state of charge greater than 30 percent of their rated capacity may only be transported under conditions approved by the Associate Administrator in accordance with the requirements in 49 CFR part 107, subpart H. Guidance and methodology for determining the rated capacity can be found in sub-section 38.3.2.3 of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). The tank car specification may be marked to indicate a test pressure of 20.68 Bar (300 psig). TP25 Sulphur trioxide 99.95% pure and above may be transported in tanks without an inhibitor provided that it is maintained at a temperature equal to or above 32.5 C (90.5 F). (a) The Hazardous Materials Table . A13 Bulk packagings are not authorized for transportation by aircraft. Transportation of these packages also requires the door of each van trailer to be marked with Warning trailer may contain chemical vapor. The Associate Administrator will base the authorization on results from Series 2 tests and a Series 6(c) test from the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) on packages as prepared for transport in accordance with the requirements of this subchapter. When a consignment is undeliverable, the consignment shall be placed in a safe location and the appropriate competent authority shall be informed as soon as possible and a request made for instructions on further action. The requirements of 173.24(g)(1) and 173.27(c) do not apply. This is in response to your November 18, 2015 e-mail and subsequent conversations with members of my staff requesting clarification of the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180) applicable to the selection of a . Essentially, such SSolder complies with RoHS (Restriction of Hazardous Substances) regulations. Additionally, unless otherwise excepted in this subchapter, polyester resin kits must be packaged in specification combination packagings based on the performance level of the base material contained within the kit. 74 During transport, this material must be protected from direct sunshine and stored or kept in a cool and well-ventilated place, away from all sources of heat. The chemical under pressure must be classed based on the hazard characteristics of the components in the propellant; the liquid; or the solid. 3090 or 3091, as appropriate. Radiation detectors transported as individual components must be transported as follows: (1) They must be packed in a sealed intermediate plastic liner with sufficient absorbent or adsorbent material to absorb or adsorb the entire gas contents. N95 UN1075, Liquefied petroleum gas and UN1978, Propane authorized for transport in DOT 4BA240 cylinders is not subject to the UN identification number and proper shipping name marking or the label requirements of this part subject to the following conditions: a. Air must be eliminated from the vapor space by nitrogen or other means. Displaying title 49, up to date as of 3/02/2023. TP21 The wall thickness must not be less than 8 mm. 54 Maneb or maneb preparations not meeting the definition of Division 4.3 or any other hazard class are not subject to the requirements of this subchapter when transported by motor vehicle, rail car, or aircraft. Lading must be blanketed at all times with a dry inert gas at a pressure not to exceed 103 kPa (15 psig). Transport in accordance with this special provision must be noted on the shipping paper. 6. TP5 For a portable tank used for the transport of flammable refrigerated liquefied gases or refrigerated liquefied oxygen, the maximum rate at which the portable tank may be filled must not exceed the liquid flow capacity of the primary pressure relief system rated at a pressure not exceeding 120 percent of the portable tank's design pressure. 9 Packaging for certain PCBs for disposal and storage is prescribed by EPA in 40 CFR 761.60 and 761.65. Additionally, self-propelled vehicles or equipment that contain a fuel cell engine must be described using the entries Engine, fuel cell, flammable gas powered or Engine, fuel cell, flammable liquid powered or Vehicle, fuel cell, flammable gas powered or Vehicle, fuel cell, flammable liquid powered, as appropriate. 119 This substance, when in quantities of not more than 11.5 kg (25.3 pounds), with not less than 10 percent water, by mass, also may be classed as Division 4.1, provided a negative test result is obtained when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). B131 When transported by highway, rail, or cargo vessel, waste Paint and Paint related material (UN1263; PG II and PG III), when in plastic or metal inner packagings of not more than 26.5 L (7 gallons), are excepted from the marking requirements in 172.301(a) and (c) and the labeling requirements in 172.400(a), when further packed in the following specification and non-specification bulk outer packagings and under the following conditions: a. d. In addition to the training requirements prescribed in 172.700 through 172.704, each driver must be trained regarding the properties and hazards of diatomaceous earth filter material, precautions to ensure safe transport of the material, and actions to be taken in the event of an emergency during transportation, or a substantial delay in transit. 386 When transported by private motor carrier only, the following corrosive liquids may be packaged in polyethylene bottles with a capacity no greater than 3.785 L (one gallon), further packed inside an open-top, heavy wall, high density polyethylene box (i.e., crate) in a manner that the polyethylene bottles are not subjected to any superimposed weight, and the boxes must be reasonably secured against shifting within the transport vehicle and loaded so as to minimize the possibility of coming in contact with other lading: Compounds, cleaning liquid, NA1760, PG II or III; Corrosive liquid, acidic, inorganic, n.o.s., UN3264, PG II; Corrosive liquid, acidic, organic, n.o.s., UN3265, PG III; Corrosive liquid, basic, inorganic, n.o.s., UN3266, PG II; Hydrochloric acid solution, UN1789, PG II; and. Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner. "Published Edition". Each empty bottle must have a minimum weight of not less than 140 grams and a minimum wall thickness of not less than 0.020 inch (0.508 mm). Formulations with low nitrocellulose contents and neither showing dangerous properties when tested for their ability to detonate, deflagrate or explode when heated under defined confinement by the appropriate test methods and criteria in the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter), nor classed as a Division 4.1 (flammable solid) when tested in accordance with the procedures specified in 173.124 of this subchapter (chips, if necessary, crushed and sieved to a particle size of less than 1.25 mm), are not subject to the requirements of this subchapter. Nickel-metal hydride button cells or nickel-metal hydride cells or batteries packed with or contained in battery-powered devices transported by vessel are not subject to the requirements of this special provision. 24 Alcoholic beverages containing more than 70 percent alcohol by volume must be transported as materials in Packing Group II. 196 The nitrocellulose must meet the criteria of the Bergmann-Junk test or methyl violet paper test in the UN Manual of Tests and Criteria, Appendix 10 (IBR, see 171.7 of this subchapter). The following provisions also apply: a. TP29 A portable tank having a minimum test pressure of 1.5 bar (150.0 kPa) may be used provided the calculated test pressure is 1.5 bar or less based on the MAWP of the hazardous materials, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. 108 Fireworks must be so constructed and packaged that loose pyrotechnic composition will not be present in packages during transportation. A copy of the approval must accompany each shipment. not more than 0.1 mL/hour per 30 mL inner packaging at 20 C (68 F) produced from gradual decomposition. For transportation by aircraft, articles, machinery, or apparatus, may not contain any material forbidden for transportation by passenger or cargo aircraft. The objects must be secured to the flat car, motor vehicle, intermodal container, or unitized by steel banding to wooden runners or pallets and the units secured to the flat car, motor vehicle, or freight container to prevent shifting, including relative motion between the objects, under conditions normally incident to transportation. Portable tank instructions specify the requirements applicable to a portable tank when used for the transportation of a specific hazardous material. These provisions apply only to transportation by aircraft: A1 Single packagings are not permitted on passenger aircraft. B2 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks are not authorized. Retain a copy of each notification of pilot-in-command if requested for up to 30 days Which one of the following hazardous materials is NOT excepted from the quantity limitations in 175.75? b. 66 Formulations of these substances containing not less than 30 percent non-volatile, non-flammable phlegmatizer are not subject to this subchapter. It may not be used to describe articles, machinery, or apparatus for which a proper shipping name exists in the 172.101 Table. b. 62 Oxygen generators (see 171.8 of this subchapter) are not authorized for transportation under this entry. Column 7 of the HMT specifies codes for special provisions applicable to packaging, packaging requirements, certification, and marking or labeling for a hazardous material. N79 Packages consisting of tightly closed metal inner packagings not over 0.5 kg (1.1 pounds) capacity each, packed in outer wooden or fiberboard boxes, or wooden barrels, are authorized and need not conform to the requirements of part 178 of this subchapter. learn more about the process here. Used or spent dry batteries of both non-rechargeable and rechargeable designs, with a marked rating up to 9-volt that are combined in the same package and transported by highway or rail for recycling, reconditioning, or disposal are not subject to this special provision or any other requirement of the HMR. Comparative fire testing between a package as prepared for transport (including the substance to be transported) and an identical package filled with water must show that the maximum temperature measured inside the packages during testing does not differ by more than 200 C (392 F). 5. A101 In addition to the applicable requirements of 173.185, the quantity of lithium metal in the batteries contained in any piece of equipment must not exceed 12 g per cell and 500 g per battery. Additionally, each cylinder must be visually inspected in accordance with CGA pamphlet, CGA C-6 (incorporated by reference, see 171.7). c. The cylinders are collected and transported by a private or a contract carrier for reconditioning, reuse or disposal. N90 Metal packagings are not authorized. B4 MC 300, MC 301, MC 302, MC 303, MC 305, and MC 306 and DOT 406 cargo tanks are not authorized. The total mass of lithium batteries contained in any package must not exceed the quantity limits in columns (9A) and (9B) for passenger aircraft or cargo aircraft, as applicable; b. 19 For domestic transportation only, the identification number UN1075 may be used in place of the identification number specified in column (4) of the 172.101 table. 200 Division 1.4G consumer fireworks may be certified for transportation by a DOT-approved Fireworks Certification Agency in accordance with the provisions of 173.65 of this subchapter. For non-pressurized lighters containing a Class 3 (flammable liquid) material, its design, description, and packaging must be approved by the Associate Administrator prior to being offered for transportation or transported in commerce. Such articles must comply with the following requirements: (1) The water capacity of the pressure receptacle must not exceed 0.5 L and the working pressure must not exceed 25 bar at 15 C (59 F); (2) The minimum burst pressure of the pressure receptacle must be at least four times the pressure of the gas at 15 C (59 F); (3) Each article must be manufactured in such a way that unintentional firing or release is avoided under normal conditions of handling, packing, transport and use. If they do leak, they must be overpacked in packagings conforming to the specification requirements of part 178 of this subchapter or in salvage packagings conforming to the requirements in 173.12 of this subchapter. (b) Preparation for transport. A82 The quantity limits in columns (9A) and (9B) do not apply to human or animal body parts, whole organs or whole bodies known to contain or suspected of containing an infectious substance. These entries include hybrid electric vehicles powered by both an internal combustion engine and batteries. 12 In concentrations greater than 40 percent, this material has strong oxidizing properties and is capable of starting fires in contact with combustible materials. 382 Packages containing toy plastic or paper caps for toy pistols described as UN0349, Articles, explosive, n.o.s.

Roger Ver Wife, You Have The Greatest Taste In Quotes, Articles C

column 7 of the hazardous materials table